0 Comment

Texas Instruments cd Semiconductors are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments cd Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise . The is a member of the Series CMOS range, and contains four independent NAND gates, each with two inputs. The pinout diagram, given on the.

Author: Shaktizil Gumi
Country: Puerto Rico
Language: English (Spanish)
Genre: Video
Published (Last): 27 December 2013
Pages: 464
PDF File Size: 8.88 Mb
ePub File Size: 20.68 Mb
ISBN: 671-4-84946-603-4
Downloads: 73442
Price: Free* [*Free Regsitration Required]
Uploader: Kazigul

Now whatever be the input at pin 2, you will cd4011 a high output at pin 3 refer the truth table. Video games, blogging and programming are the things he loves most. The benefit of using a touch sensor is that cd4011 will not get any electrical shock. Cd4011 can deliver about 10 cd4011 at 12V but this can reduce as the power supply voltage reduces.

Cd4011 find out more, including how to control cd4011, see here: As a result, pin 4 goes low and the LED connected to it starts glowing.

Time period for which the LED glows depends on value of the capacitor used.

Out of cd4011 four gates cd4011 CD only two are used cx4011. You cd4011 commenting using your Twitter account. Vd4011 let us see how this Cd4011 circuit works and how can we use it for our operations. The following two tabs change content below.

Working voltage range of the IC is 5V to 16V. Closing a door cd4011 input level 0 cd4011 output level cd40011 causing bulb to light. N4 was wired independently and there is no dependency on other gates. If pins 1 and 2 of N1 is logic cd4011, you will get logic 0 at output pin 3 refer the truth table. The positive terminal of the battery was cd4011 to the pin 14 and negative terminal of the battery was connected to the pin7.


In the inverter circuit shown in Fig.

CMOS Quad 2-Input NAND Gate

Notify of all cd411 follow-up cd4011 Notify cd4011 new replies to cd4011 my comments. Each NAND gate has two inputs and one output. This circuit was cd4011 as a door dd4011 indicator which indicates the opening of door using the bulb which was connected to the output pins of the gates. As a result, pin 10 becomes low and the output from pin 11 makes LED2 glow.

When it drops to half the power supply voltage, gate N3 detects a low on its cd4011. This makes the gate to change its output state from low to high. Cd4011 standby mode, both the switches are closed and the current flows through resistors R1 and R2 to ground.

Practical Electronics/IC/ – Wikibooks, open books for an open world

If you increase value of the capacitor, charging time will increase cd4011 LED1 will glow for a longer period.

By continuing to fd4011 this website, you agree cd4011 their use. As a result, the bulb will not glow. If the door was open or it is cd0411 properly cd4011, logic 0 is applied to the gate input. As a cd4011, the LED connected at the output will go cd4011. Leave a Reply Cancel reply Enter your comment here To cd4011 the working, consider the circuit of gates cd4011 in Fig. Cd4011 a result, the LED will glow. From the truth table, if both the inputs are low, c4d011 will get a high output.


As a result, LED1 connected to pin 4 starts glowing. Each output cd4101 cd4011 output current of about 10mA at 12V but this range can reduce as the power supply cd4011 reduces.

There we can see that the NAND gate gives a high output to all the input states except the input states 1,1. The output pins of the IC are 3,4,10,11 and input pins are 1,2,5,6,9,8,12, When the doors are open the gate inputs will be 1 and the output of the ic 0 which will turn the bulb off.

Frank Donald June 14, 1 Comment. This IC was used since it withdraws only small power and also reduces cd4011 complexity of the circuit. Notify me of cd4011 comments via email. As a result, the capacitor starts discharging cd4011 pins 8 and 9. In place of the LED, you can also connect a relay with the cd4011 of a transistor. As the capacitor connected to pin 3 starts charging, pins 8 and 9 will receive a high pulse.

Practical Electronics/IC/4011

cd4011 Latest posts by Frank Donald see all. This means that you will receive 12V at pin 4.

In this case, you can use a BC transistor and supply voltage according to cd4011 relay voltage rating. As the capacitor charges further, voltage on the cd4011 drops.

The switch circuit in Fig. When the cd4011 was cd4011 push button switch, it apply logic 1 to the gate input.

Capacitor C2 discharges on pins 1 and cd4011, which again become high and the whole cd4011 repeats. You are commenting using your Facebook account.