Menu

HT12E AND HT12D DATASHEET PDF

0 Comment

DataSheet: PDF icon HT12E is an encoder integrated circuit of series of encoders. They are paired with series of decoders for use in. Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and HT12F is used to decode 12 bits of address information.. 盛群半導體為國內. HT12D. 8. 4. L. Ö. RC oscillator DIN active ²Hi² 18 DIP/20 SOP .. The recommended oscillator frequency is fOSCD (decoder) @ 50 fOSCE (HT12E encoder). @ The information appearing in this Data Sheet is believed to be.

Author: Dairg Akinodal
Country: Mexico
Language: English (Spanish)
Genre: Video
Published (Last): 20 October 2013
Pages: 234
PDF File Size: 2.35 Mb
ePub File Size: 9.33 Mb
ISBN: 236-4-42931-314-9
Downloads: 41450
Price: Free* [*Free Regsitration Required]
Uploader: Zolole

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. To find out more, including how abd control cookies, see here: Supply voltage; 5V 2. An LED can also be connected across this terminal to indicate output.

These are the 8-bit address bits, which is used to protect your data. They are capable of Encoding 12 bit of information which consists of N address bits and N data bits. The Encoded 12 bit output data can be obtained from this pin. Be the first to write a review. This is an CMOS logic integrated circuit encoder. HT12E is an encoder integrated circuit of 2 12 series of encoders.

  1761-NET-ENI EBOOK DOWNLOAD

HT12E Encoder IC

Return and Refund Policy. The encoded bit can be obtained from the Dout pin pin Skip to content Gone are the days when we used to use wires to connect two devices to establish a communication path.

We will notify you the result by email. Used for interfacing RF circuits generally MegaHz.

This oscillator can be used by connecting these two pins through a 1M Resistor. Choosing Motor For Robots.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

This pin outputs the parallel data serially. This IC has a total of 18 pinsnine on either sides: This cycle is repeated as long as TE is kept low. It is mainly used in interfacing RF and infrared circuits. The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an RF transmission medium and gives output to the output pins after processing the data.

A basic datasjeet diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. They can also be connected to switches to manually send and receive data. Basically found in applications of remote control systems.

This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. HT12E IC has four bit parallel data inputwhich it then converts to serial data output.

  WXPYTHON 2.8 APPLICATION DEVELOPMENT COOKBOOK PDF

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

They are paired with 2 12 series of decoders for use in remote control system applications. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

Pull the Transmission Enable pin pin 14 to ground to activate transmission. What is Web Browser. Virgin Galactic — Commercial Space Flight.

Full Name Email Address. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. Generally a resistor of value 51 KOhms can be used. SPI Module of Arduino. This IC hasmany applications in short range remote controlling. Interface SD Card with Arduino. Whenever an active low signal is applied at its TE pin then only the parallel data gets transferred serially at the output, otherwise the IC is in high impedance state.

hy12d

Submitted by admin on 30 October These pins are generally shorted by a resistor.