ISO 10555-5 EPUB

0 Comment

ISO. Second edition. Reference number Permission can be requested from either ISO at the address below or ISO’s member body in the. 31 Jul Purchase your copy of BS EN ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. EN ISO Intravascular catheters – Sterile and single-use catheters – Part 5 : Over-needle peripheral catheters – ISO specifies requirements.

Author: Samugrel Jumi
Country: Turkey
Language: English (Spanish)
Genre: Software
Published (Last): 28 January 2007
Pages: 415
PDF File Size: 9.96 Mb
ePub File Size: 1.13 Mb
ISBN: 802-5-71185-793-6
Downloads: 31566
Price: Free* [*Free Regsitration Required]
Uploader: Shakajinn

Iso 10555-5 colour references for opaque naaterials are given in annex C. Details of which is given in National Iso 10555-5 A. Blood flow into the needle hub. Fixed or removable fitting per- mitting venting of air while restricting or preferably preventing the escape of blood.

The fluid pathway in the iso 10555-5 shall be free of unintended obstructions that would prevent flashback. Designation and catalogue of CCR colours.

Limited collection of colours. For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated expressing iso 10555-5 result of a test or analysis, shall be rounded off in accordance with IS 2: Iso 10555-5 standards are subject to 105555-5, and 1055-55 to agreements based on this part of ISO are encouraged to investigate the possibility of applying iso 10555-5 most recent editions of the standards indicated below.

Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards: Round the calculated average water fiowrate to the nearest whole iso 10555-5 of millilitres. Fitting attached to the needle tube, providing communication with its bore. Bureau of Indian Standards BIS is a statutory institution established under iso 10555-5 Bureau of Indian Standards Act, to promote harmonious uso of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country.

Copyright BIS has the copyright of all its publications.

I Principle Water is allowed to flow through the catheter and the amount of flow is measured either volumetrically or gravimetrically. Rigid tube with one end sharpened to facilitate entry into body tissue.


Figure 1 — Typical over-needle peripheral intravascular catheter NOTE 2 At the time of publication of this part of ISO iso 10555-5, there is no acceptable, validated test method to determine radio-detectability.

Attention is particularly drawn to the following: In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist. The corresponding Indian Standards which are to be substituted in their places iso 10555-5 listed below along with iso 10555-5 degree of equivalence for the editions indicated: The assembly comprising at least a needle tube attached to and communicating with a needle hub.

When the needle is fully inserted into the catheter unit, the catheter tube shall neither extend beyond the heel of the needle bevel nor be nnore than 1 nnnn fronn it see dinnension a in iso 10555-5 1. The number of iso 10555-5 places retained in the rounded off value should be the same as that of the specified value in this standard.

Intravascular catheters ISO , -3, -4, -5

Catheter designed for the introduction or withdrawal of liquids or devices into or from the peripheral vascular system. I Principle A force is applied iiso tensile and connpress- ive to the needle tube and needle hub and the tube- hub union is then iso 10555-5 for iso 10555-5.

Other parts of this standard are as follows: The fluid is allowed to flow into the needle, and the time taken for fluid to leak through iso 10555-5 vent fitting is measured.

Add the following reference: Certain conventions are, however, not identical to those used in Indian Standards. This Indian Standard has been developed from Doc No.: An approved test method for producing a value of radio-detectability will be established. Page 3, subclause 4.

Standards are also reviewed periodically; a standard alongwith amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.

Annex D shows examples of typical needle point geom- etries. Iso 10555-5 Standard ISO NOTE To improve the visibility of the solution, a colorant such as red or iso 10555-5 food dye may be incorporated.

Assembly comprising the cath- eter tube, catheter hub and any integral fittings. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. The details of conditions under which the licence for the iso 10555-5 of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards.


The catheter tube may have a iso 10555-5 lumen or multiple lumens.

BS EN ISO 10555-5:2013

No part of the these publications may be reproduced in any form iso 10555-5 the prior permission in writing of BIS.

An example of a suitable apparatus is shown in fig- ure B.

Review of Indian Standards Amendments are issued to standards iso 10555-5 the need arises on the basis of comments.

Until that time, a manufacturer may label his product “radio- opaque” provided he can support this claim by demonstrat- ing that iso 10555-5 isl an appropriate method for showing radio- opacity. Available from Munsell Color, N. Pages 1 and 2 4. Peripheral intravascular catheter designed for the introduction of withdrawal of liquids or devices into or from the peripheral vascular system. E-5 Test report The test report shall contain at least the following information: When tested in accordance with annex E, fluid shall not leak out of the iso 10555-5 fitting within 15 s.

Part 1 General requirements do The iso 10555-5 committee has reviewed the provisions of the following International Standard referred in this adopted iso 10555-5 and has decided that it 105555-5 acceptable for use in conjunction with this standard: Search the history of over billion web pages on the Internet.

Measure the time taken for iao to form the first falling drop at the back of the vent fitting. Assembly comprising at least a needle tube attached to, and communicating with, a needle hub. NOTE 3 The point should be designed to be noncoring. If a steel tube is used, it isp connply with ISO At the time of publication, the editions indicated were valid.